filters
state:
Show
city:
Show
category:
Show
product:
Show
we purchased a sissor lift for our quick service month's ago...from day one it made a horrible squeal sound when lifting...We called the installer who came out and determined that one of the pin's was gaulded and scored and it needed to be replaced...After five months...
Read more
Anonymous

matts shop Same Issues! I have had nothing but anger towards this lift. I have 14 lifts and this is the only BenPak and I hate it.

1.0
I didn't like
  • Poor quality
#942294
Reply to reviews
Customer service of BendPak is disguisting. A less than 1 year old BendPak scissor lift collapsed twice at our facility with noticeable structural defect. I requested a replacement lift under warranty and advised they retrieve current lift so their QC team can inspect...
Read more

I purchased a 4 post lift, ranger cabinet washer and a tire balancer all from bendpak. Each piece of equipment has failed one within the warranty period, they sent me the part I had to replace, this was the tire balancer only after second use. next was the lift. the ...
Read more
Bought a 2 post lift and once received and started to install found out the posts were not properly layed out and centered on the mounting plate that bolts to the cement floor. This is supposed to be done during the manufacturing process before the post is welded to...
Read more
Anonymous

mike w I own a 10,000 2 post low profile lift of theirs and only purchased after i had installed 2 others and found the quality to be far better then others i have installed. Sounds ...

OREDERED NEW BENDPAK EXTENDED ALIGNMENT FOUR POST RACK HAD ISSUES WITH CABLE FRAING AND PULLEYS WEARING OUT NO HELP ON REPLACEMENT PARTS THIS HAS HAPPENED THREE TIMES, ALL THE OTHER RACKS IN MY SHOP THIS HAS NEVER HAPPEN WITH. THE TECH DEPT STATES YOU HAVE TO LUBE...
Read more
1.0
I liked
  • Not concerned about safety
I didn't like
  • Poor safety concerns
#821888
Reply to reviews
Purchased a BENDPAK 10,000 LB lift in 2010. Great lift except it TAKES OVER 3 MINUTES to lower. Was advised to try atf that did nothing to help. Does anyone have any solutions to help this issue. When we do jobs that take 10 times lowering in a day a tech spends 30...
Read more
I didn't like
  • Slow lift
#748070
Reply to reviews
I truly love the lift, however the rubber they use failed when lifting my F350 truck. I only use lift a few times a year for my own cars / trucks and very dissatisfied with the rubber compound. They said I must have put it on a small area or joint, truth is the...
Read more
3.7
I didn't like
  • Poor quality rubber pads
#693777
Reply to reviews
After six years and countless leaking lines, Hydraulic locks that have been replaced 5 times in six years, And now there telling me that I should just replace it because it's rusted and the left side raise's 1 1/2 inch lower than the right. Of course it's our fault! we...
Read more
1.0
#555241
Reply to reviews
BendPak Sold Us Uncertified Auto Lifts
We bought 4 BendPak auto lifts. The city demanded we get a permit for them. The inspector from the L.A. Dept. of Bldg. and Safety refused to issue a permit because the lifts did not bear a certification from a known lift testing lab (the importance of which, BendPak...
Read more
Anonymous

Mondiesel Sounds like the person buying the lifts didn't do his/her homework or ask the right questions and needed to blame someone else. Sounds like the LA court system is biased when...

Anonymous

Alison Can you tell me the name of the company that did have the proper certification to get permitting clearance? I am also looking into this same issue. Thanks

Contact Bendpak

Headquarters Address:
BendPak, Inc.
1645 Lemonwood Drive
Santa Paula, CA 93060
Phone:
(888) 856-5820
More

Companies similar to Bendpak

We purchased two 7k BENDPAK scissor lifts for our shop. Spent over $9,000. Have had nothing but problems with one of them. It has been down 10 times in 12 months. All of the concerns have been safety concerns. Peoples lives in danger here....BENDPAK really has no...
Read more